Renew It!

4L, 10L

Renew It! Wood & Concrete Resurfacer is the ultimate rescue for worn or weathered wood and concrete.

The high performance, 100% acrylic formula fills in cracks up to 5mm deep, locks down splinters and provides an extremely durable surface that resists fading and creates a mildew resistant coating while giving new life to time-worn material.

Features:

  • Weather proof protection
  • Provides a mildew resistant coating
  • Resists fading, cracking and peeling
  • Barefoot friendly
  • Slip resistant
  • Locks down splinters
  • Fills cracks up to 5mm deep
  • Tintable to 100s of colours
  • Flat finish
  • Ideal for decks, docks, porches, pathways and more

 

Suitable Surfaces

White Knight Renew It! Wood & Concrete Resurfacer is formulated for the following horizontal and vertical concrete and wood surfaces: aged, rough, broom-swept concrete; new concrete surfaces cured for 30 days; retaining walls; structurally sound old, weathered wood (decks, stairs, docks, posts, railings, and more); new wood when a non-slip, textured surface is desired.

DO NOT APPLY TO: garage floors, driveways or any other areas with vehicular traffic; submerged surfaces such as ponds, fountains or swimming pools; interior concrete surfaces; any surface that has been recently coated with paint, stain, sealer or water repellent.

Not recommended for whole-house vertical surfaces such as cement render or weatherboard.

Safety & First Aid

  • KEEP OUT OF REACH OF CHILDREN.
  • If swallowed seek medical advice immediately and show the container or label. Do NOT induce vomiting.
  • If on skin wash skin thoroughly with soap and water or use recognised skin cleanser. Do not use solvents or thinners.
  • If in eyes immediately flush with running water for at least 15 minutes. Seek immediate medical attention.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096

Environment

  • Do not pour unwanted paint down the drain.
  • Keep unwanted paint in sealed containers for disposal via special chemical waste collections.
  • Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via can recycling programs.
  • Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.

How To Video

Rescue your old deck with White Knight Renew It!



Preparation

  • Sand or scrape any loose or flaking stain or paint.
  • The surface area must be clean and free of dirt, grease, mildew and algae to ensure proper adhesion.

FOR WOOD:

Cleaning with a pressure washer is not recommended. Pressure washing the wood surface can drive contaminants into the wood, eventually leading to coating failure. Sand any loose wood fibres.

Clean the surface with White Knight Renew It Deck Cleaner following label directions. Loose deck screws, raised nail heads or loose decking boards should be secured. Remove loose splinters and replace rotting or severely damaged boards.

Wood cracks and depressions deeper than 5mm should be filled with an exterior paintable sealant caulk.

 

FOR CONCRETE:

Clean surface by applying White Knight Concrete Etcher following label directions or a pressure washer may be used.

Patch cracks and depressions larger than 5mm with a polymeric concrete patching compound following manufacturer's instructions. Do not use caulks or other non-concrete patching compounds.

Both wood and concrete surfaces must be thoroughly dry before application and there should be no threat of rain for 24 hours.

Please use caution when applying around aquatic habitats to avoid spills.

Application

  1. Stir thoroughly with a broad flat stirrer in a circular lifting motion for 5 minutes before use and continue to stir at regular intervals during application.
  2. Apply 2 coats by brush or roller.

Before applying the first coat, dab a heavily loaded brush into any deep cracks, gaps, nail/screw holes and knots until filled. For cupped, cracked or warped boards, drive product into cracks by rolling across the narrow width as well as the length of the board. 

Lightly brush any product that drips between the boards.

Cut in around the edges of the deck or concrete surface with a brush using a short dabbing stroke.

To apply the first coat, fully saturate the roller by rolling back and forth in the tray. Using light and even pressure, apply product to a few boards or half a square meter at a time, keeping a wet edge to avoid lap marks. Lightly back brush after rolling if you desire a smoother appearance.

To apply the second coat, cut in around the edges of the entire surface again and roll out as for the first coat. 

During painting keep brushes and rollers working freely by rinsing periodically in water. Protect paving and decks from spills. Avoid painting in direct sun or windy conditions. Dampen highly absorbent surfaces.

DO NOT USE AT TEMPERATURES BELOW 10°C OR ABOVE 35°C OR IF RAIN IS IMMINENT.

 

Coverage

Approximately 6m² per litre. Coverage will be lower on rough or absorbent surfaces.

Drying

Allow 6 hours for the first coat to dry before applying the second coat. Allow longer in cool or humid conditions. Drying times will vary depending on weather and the condition of surface.

Allow the final coat to dry at least 12 hours before foot traffic and 48 hours before replacing furniture or heavy objects .If surface is not dry due to low temperature or high humidity, allow extended drying time before placing furniture or heavy objects on to the coated surface.

Full cure and maximum stain resistance may take 30 days.

Clean up

Scrape excess paint from equipment into a separate container. Clean brushes and equipment with water immediately after use.

FIND A STORE