Ultra Pave Quick Dry

1L, 4L, 10L

Ultra Pave Quick Dry is a quick drying acrylic formulation with a satin finish. Ideal for refreshing tired concrete areas.   

Ideal for use on garage floors (when used with Ultra Pave Garage Floor Primer), driveways, paths, patios, court yards and more.

Features:

  • Touch dry in 30 mins, re-coat after 2 hours
  • DuraTough Technology
  • Tintable to 1000s of colours
  • Satin finish
  • No primer required - excluding use on garage floors
  • Easy clean up with water
  • Excellent adhesion to concrete
  • Durable, hardwearing
  • May be applied over oil and water based paint
  • Ideal for use on garage floors (when used with Ultra Pave Garage Floor Primer), driveways, paths, patios, court yards and more 

Suitable Surfaces

Suitable for use on concrete areas such as garage floors (when used with Ultra Pave Garage Floor Primer), driveways, paths, patios, court yards and more.

Safety & First Aid

  • KEEP OUT OF REACH OF CHILDREN.
  • If swallowed, seek medical advice immediately. Do not induce vomiting.
  • If in eyes, flush with cold water. Seek medical advice immediately.
  • If on skin wash with soap and water or recognised skin cleanser. Do not use solvents or thinners.
  • After use, firmly re-seal lid and store in a cool dry place out of direct sunlight.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096

Environment

  • Do not pour unwanted paint down the drain.
  • Keep unwanted paint in sealed containers for disposal via chemical waste collections.
  • Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via steel recycling programs.
  • Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your council first.

How To Video

Spruce up your veranda and path by painting your concrete. Watch professional painter Roy Evans show you how in a few easy steps using White Knight Paving Paints.



Preparation

To obtain best results the surface must be prepared correctly before application:

  • Allow new concrete to cure for 4 weeks before painting.
  • Repair or replace unsound concrete.
  • Remove any previously applied sealant or curing compound by mechanical sanding or grinding.
  • Remove any loose concrete by scraping, grinding, high pressure water blasting, wire brushing or sanding.
  • Clean the surface with a strong detergent and hose off with clean water. 

SMOOTH CONCRETE & GARAGE FLOORS (new, old or bare)

  • Etch surface with Ultra Pave Concrete Etcher following label directions.
  • After etching, scrub surface thoroughly with a stiff bristle broom and pressure hose with clean water to remove all loose material and residue.
  • Check surface has slightly roughened. If it doesn't feel like 180# sandpaper repeat the etching process.
  • Test for loose residue with adhesive tape. If loose material is picked up on the tape, repeat the cleaning process.
  • Allow concrete to dry completely.
  • The surface must be clean and free from dust, dirt, grease, oil, moss, loose material and other contaminants.
  • Prime surface with Ultra Pave Garage Floor Primer following label directions.

ROUGH CONCRETE (new, old or bare)

  • Scrub the surface with a stiff bristle broom to remove any loose residue then rinse thoroughly with a strong water jet (eg garden or pressure hose).
  • Test for loose residue with adhesive tape. If loose material is picked up on the tape repeat the cleaning process.
  • Allow concrete to dry completely.
  • The surface must be clean and free from dust, dirt, grease, oil, moss, loose material and other contaminants.

PREVIOUSLY PAINTED CONCRETE

  • Check for lifting of old paint. If it is not sound, remove all old paint.
  • Scrape off all loose and flaking paint by wire brushing or sanding.
  • Sand glossy or smooth surfaces thoroughly.
  • Rinse surface thoroughly with a strong water jet (eg garden or pressure hose).
  • Allow concrete to dry completely.
  • The surface must be clean and free from dust, dirt, grease, oil, moss, loose material and other contaminants.
  • Test paint on a small inconspicuous area to ensure compatibility with the old coating. After 24 hours of drying, check for lifting of old paint or poor adhesion. If problems are observed total removal of the old paint is required.

Application

  1. Stir thoroughly with a broad, flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
  2. Apply 2 coats by brush or roller. Thin the first coat on bare concrete with 20% water to aid penetration and adhesion. For added slip resistance add Ultra Pave Topcoat Grip Additive to the second coat following label directions.

DO NOT USE AT TEMPERATURES BELOW 10°C OR ABOVE 30°C

Coverage

Approximately 10m² per litre, depending on the porosity of the surface.

Drying

Touch dry in 30 minutes. Re-coat after 2 hours. Light traffic after 6 hours. Heavy traffic after 7 days. Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

Clean Up

Clean brushes and equipment with water immediately after use.

Care & Maintenance

Wash as often as required with water and mild detergent. Do not use harsh abrasive brushes or high pressure water hoses. Long exposure to pooling water or chemicals will damage the paint and they should be removed or cleaned quickly.

FIND A STORE