Quick Dry – Advanced Enamel

500ml tin, 1L tin, 4L tin

Rust Guard Quick Dry Advanced Enamel delivers outstanding rust protection to metal surfaces whilst also drying quicker than any other rust preventative paint in the Australian market.

Ideal for use on metal fences, roofs, doors, gutters, downpipes, windows, railings and gates.


  • Quick drying
  • Non yellowing
  • Touch dry in 30mins, re-coat after 2 hours
  • No primer required for new or lightly rusted steel and wrought iron
  • Renews rusted surfaces
  • Low VOC
  • Protects new metal
  • Low odour
  • Available in both gloss and satin tintable bases
  • Excellent adhesion, durability and opacity
  • 8 year guarantee
  • Satin finish matches Colorbond®
  • Tintable to 1000s of colours including Taubmans® and Colorbond

Suitable Surfaces

Rust Guard Quick Dry Advanced Enamel may be used on all metal surfaces.

Safety & First Aid

  • Keep lid on when not in use.
  • If swallowed - Drink plenty of water. Always seek medical advice.
  • Eye contact - Flush with plenty of water. Always seek medical advice.
  • Skin contact - Wash with soap and water. Always seek medical advice.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096



  • Do not pour unwanted paint down the drain.
  • Keep unwanted paint in sealed containers for disposal via chemical waste collections.
  • Empty waste containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via steel recycling programs.
  • Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your council first.


8 Year Guarantee

White Knight Rust Guard Quick Dry Advanced Enamel is guaranteed to inhibit the development of rust for 8 years if applied to suitable and properly prepared surfaces, following White Knight instructions and the appropriate White Knight Preparation and Primer products are used (if required). This guarantee is given by PPG Industries Australia Pty Ltd and applies to defects in the manufacture or formulation of the product. This guarantee does not cover: blistering, peeling or flaking; application in highly corrosive areas; paint failure caused by any breakdown of coatings applied previously or use of other coating not specified by White Knight; or any other factors beyond our control. Any damage to the coating must be repaired immediately to inhibit rust development. If this guarantee is not met, we will replace the paint or refund your money. We are not liable for the cost of any labour or any other direct or indirect loss or damage arising from a breach of this guarantee. Customers are responsible for all costs of claiming under this guarantee. To claim, customers must write to us or call our Customer Care number to request a claim form. The benefits provided by this guarantee are in addition to other rights and remedies under the law.

If you are a consumer within the meaning of the Australian Consumer Law:  Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.


  • Remove all loose rust and flaking paint by wire brushing.
  • Sand new metal, previously painted or glossy surfaces thoroughly.
  • The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
  • Treat rusted surfaces with Rust Guard Rust Converter.
  • Prime galvanised iron, ZINCALUME® and non ferrous metals e.g. aluminium with Rust Guard SLS Etch Primer or Rust Guard Quick Dry True Bite.
  • In severe conditions, or if heavily rusted, prime steel and wrought iron with Rust Guard Quick Dry True Bite or Rust Guard Metal Primer.


  1. Stir thoroughly with a broad, flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
  2. Apply 2 coats by brush, roller or spray gun.




Approximately 16m² per litre, depending on the nature of the surface.



Touch dry in 30 minutes. Re-coat after 2 hours.

Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.


Clean Up

Clean brushes and equipment with water immediately after use.

Quick Dry – Advanced Enamel
Rust Protection