Hi Temp

300g aerosol

White Knight Hi Temp is a heat resistant silicon based flat finishing coat designed for use on metal surfaces subject to extreme heat.

Ideal for use on boilers, exhaust manifolds, ovens and slow combustion stoves.

Features:

  • Quick drying - Touch dry in 15 minutes
  • Heat resistant to 540°C
  • Durable
  • Excellent coverage
  • Suitable for interior and exterior use

Suitable Surfaces

White Knight Hi Temp may be used on boilers, exhaust manifolds, ovens and slow combustion stoves.

White Knight Hi Temp is not suitable for use on BBQ hot plates or food contact surfaces.

Safety & First Aid

  • KEEP OUT OF REACH OF CHILDREN.
  • If swallowed, drink plenty of water and seek medical advice immediately. Do not induce vomiting.
  • If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
  • Avoid breathing vapour or mist.
  • Use only with adequate ventilation.
  • If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners.
  • Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.

For 24 hour medical emergency response in Australia call 1800 807 001 and in New Zealand call 0800 154 666

Caution

EXTREMELY FLAMMABLE. Keep can away from flame and heat and eliminate any source of ignition. Keep can in a cool place and out of sun. Contents of can under pressure. Do not puncture or incinerate the can, even when empty.

Environment

  • Residual paint should be sprayed onto newspaper, allowed to dry and then disposed of via domestic waste collections.
  • Empty aerosol cans are recyclable via steel can recycling programs.
  • Important: Deliberate misuse of this product to damage public or private property is a crime.

Preparation

  • Thoroughly clean the surface and ensure it is free from grease, oil, dirt, rust scale and other contaminants.
  • Lightly sand previously painted and glossy surfaces.
  • Wipe surface with mineral turps and allow to dry before painting.
  • Cover all necessary areas to protect from overspray.

Application

BEFORE SPRAYING

  1. Shake can vigorously for 1 minute to ensure colour uniformity. Shake can occasionally during use.
  2. Remove the cap carefully. Avoid using sharp objects that may puncture the can.
  3. Test spray on a small inconspicuous area to ensure surface compatibility and finish suitability.

SPRAYING

  1. Select the nozzle setting: The horizontal setting should be used when spraying up and down and the vertical setting should be used when spraying across. To change the nozzle setting, turn the red section on the nozzle.
  2. Hold the can upright approximately 25cm from the surface.
  3. Press button firmly and spray several light coats with a smooth sweeping motion, overlapping each spray pass. To prevent paint from sagging, avoid spraying too close to the surface or applying a heavy coat.
  4. Repeat if necessary.

Do not use when air or surface temperature is below 15°C or above 30°C or in excessive humidity.

Coverage

Approximately 1.5m² per can, depending on the nature of the surface and amount of overspray.

Drying

Touch dry in 15 minutes. Re-coat after 1 hour. Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied. Hard dry conditions can be achieved when the coated article is heated.

Clean Up

Overspray can be removed while still wet with mineral turps.

To clean the nozzle after use and prevent blocking turn the can upside down and press button until only gas escapes.

FIND A STORE
Hints and Tips
  • Paint will not adhere to glossy or dirty surfaces.
  • It is better to spray a few light coats than one heavy coat.
  • Practice makes perfect. Do a test piece first on cardboard to get the feeling.
  • Use masking tape or newspaper to prevent paint from going on areas you don't want it to.
  • Have lots of rags handy for any cleaning.